Katalor Enterprises is a professional section steel supplier in China , we can supply A283GrA/B/C/D, A36, S235JR, S235J0, S235J2, S275JR, S275JO, S275J2, S355JR Channel steel /beam steel/Square pipe ,and ABA32A36DD32D36 angle steel for shipbuilding.
Carbon Steel S235JR Sheet Plate, S235JR Mild Steel Plate Standard Specification For Carbon Steel S235JR Sheet Plate. Standard :DIN 17100, DIN 17102, ASTM, GB/T700, JIS G3106, EN 10025, EN 10025-2:2004 Hot rolled products of structural steels. Technical delivery conditions for non-alloy structural steels. Width :1000-4000mm. Thickness :3-620mm. Length :3000-18500mm
Dec 14, 2019 · Physical Properties of S235JR Steel (1.0038 Material) Material density:7.85g/cm3; Melting point:1420-1460 °C (2590-2660 °F) S235JR Steel (1.0038 Material) Mechanical Properties. The yield strength, tensile strength, elongation, and Charpy impact test are listed in the following data sheet. EN 1.0038 material Brinell hardness:120 HBW
EN 10025 Grade S355J2G3 Carbon Steel Seamless Pipes, BS 22 rows · EN 10025 S235JR has a specified En 10025 Steel Chemical Composition of 0.17 0.20 wt.% carbon
EN 10210-1 Grade S235JRH Carbon Steel Seamless Pipes and EN 10210-1 Grade S235JRH Pipes and Tubes are low-cost Low Carbon Steel Pipes and Tubes with max 017 % carbon content with combination of max 140 % manganese easy to form and shape .These pipes are manufactured as per EN Specification and commercially referred as cs pipes or ms pipes.Low Carbon Steel Pipes are not as hard as hig carbon steel pipes,Though carburizing can increase its surface
B= Sample Steel Width; a= Sample Diameter or Thickness. Steel rolled with Q195 and Q235B grade
S235 Structural Steel Plate SupplierJan 30, 2017 · A structural grade (S) with at minimum yield strength of 235 N/mm²m, the JR designation confirms that the steel has undergone longitudinal Chary V-Notch impact testing at 27J (Joules) at room temperature. S235AR A structural grade (S) with the same minimum yield strength of 235 N/mm²m, but supplied in an as rolled condition.
S235JR Mild Steel - Special steel china supplier-OTAI S235jr steel is a mild steel, its carbon composition below 2%. So the S235JR Mild steel have very good welding performance. For S235JR, we supply the steel plate, steel round bar, steel hexagonal bar, flat bar, square bar and pipe. DIN EN S235JR Mild Steel is European standard of alloy structural steel, It is equivalent with the Chinese
S235JR steel plate, under EN10025 standard S235JR steel plate, under EN10025 standard, we can regard S235JR steel plate as Carbon and low alloy steel. S235JR steel plate is one mainly of Carbon and low alloy steel, S235JR steel plate is a type of steel sheet under EN standard which is used to build ship, bridge, belongs to high strength sheet.
S235JR Spiral welded pipe - ltgtsteelchinaWelded steel pipe. Spiral welded pipe. S235JR Spiral welded pipe. it can use a narrower strip steel production of large diameter steel pipe.The specification is eed by the outer diameter * wall thickness, and the welded pipe shall ensure that the hydrostatic test, the tensile strength of the weld and the cold bending performance meet
S235JR steel - Steel gradesStainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. S235JR can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc.
S235JR Material Introduction EN 10025 S235JR material (1.0038 steel) is an European standard hot rolled non-alloy structural steel grade. It has good plasticity, toughness and weldability, certain strength and good cold bending properties.We have large quantities of
what materials of S235JR?S235JR carbon steel plate is the European standard of non-alloy structural steels, equivalent to GB Q235B steel plates, namely carbon structural steels with low carbon, used for welding, bolting, and more riveted structure. Q235 carbon steel plate quality grades A, B, C, D, E, followed by a poor-quality, e-quality is highest.EN 10025 Steel Pipe S235JR/ S235J0/ S235J2 structural S235JR is a type of non-alloy steel, intended to be used for structural applications. This particular steel grade ic categorised in Part 2 of the Euronorm specification EN 10025. The letter capital S in the term EN 10025 S235JR Pipe signifies a structural steel that exhibits a minimum yield strength properties of around 235 MPa.