Standard Number:ASTM A1010/A1010M - 13(2018) Title:Standard Specification for Higher-Strength Martensitic Stainless Steel Plate, Sheet, and Strip:Status:Current:Publication Date:01 November 2018:Normative References(Required to achieve compliance to this standard) No other standards are normatively referenced:Informative References(Provided for Information)
ASTM A328/A328M :Standard Specification for Steel Sheet ASTM A328/A328M, Revision 13A, November 1, 2013 - Standard Specification for Steel Sheet Piling. This specification covers carbon steel sheet piling of structural quality for use in the construction of dock walls, sea walls, cofferdams, excavations, and like applications (see Specification A572/A572M). When the steel is to be welded, it is presupposed that a welding procedure suitable for the grade of steel and
ASTM A328/A328M-13a (2018) Standard Specification for Steel Sheet Piling 1.1 This specification covers carbon steel sheet piling of structural quality for use in the construction of dock walls, sea walls, cofferdams, excavations, and like applications (see Specification A572/A572M).
ASTM B114 - 07(2018), Standard Test Method for Publication Date:Monday, January 1, 2018. This test method covers the determination of the change of resistance with temperature of sheet materials used for shunts and precision resistors for electrical apparatus. It is applicable to materials normally used in the temperature range of from 0 to 80°C. https://astm/Standards/B114.htm.
ASTM B582 - 07(2018) Standard Specification for Nickel 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices
Buy ASTM F 2034 :2018 Standard Specification for Sheet Linoleum Floor Covering from SAI Global
ASTM Volume 01.03 SteelPlate, Sheet, Strip, Wire ASTM Volume 01.03 SteelPlate, Sheet, Strip, Wire; Stainless Steel Bar 2018. Under the heading of steel plate, sheet, and strip, this volume covers specifications that stress mechanical property requirements and applications. The majority of them have been adopted by the Department of Defense.
ASTM-A424 Standard Specification for Steel, Sheet, for This specification covers standard requirements for sheet steel in coils and cut lengths for porcelain enameling. Heat analysis of Type I, Type II, and Type III steels shall conform to the prescribed chemical composition for carbon, manganese, phosphorus, sulfur, and others.
Commercial Steel This quality is defined in ASTM Standards A1008 for Cold Rolled, (CS Type A, B, or C) A1011 and A1018 for Hot Rolled and is equivalent to the former Commercial Quality . Sheets of this quality are suitable for applications where bending, moderate forming or drawing may be involved .
Draft Sri Lanka Standard SPECIFICATION FOR Singapore Institute of Standards & Industrial Research and Standards Australia are gratefully acknowledged. 1 SCOPE This Sri Lanka Standard specifies requirements for aluminium/zinc alloy coated steel sheets, intended to be fabricated for use in the building industry for exterior applications such as roofing, wall cladding and awnings.
SECTION 07110 - Sheet Membrane Waterproofingcomposite sheet membrane consisting of 0.41 mm (0.016) of highdensity - polyethylene film, 0.64 mm (0.025) of specially formulated synthetic adhesive and 0.03 mm (0.001 in.) of protective coating.
Summary and Assessment of EN 17033:2018, a New Standard for Biodegradable Plastic Mulch Films . In January 2018, the European Standard EN 17033:Plastics Biodegradable mulch films for use in agriculture and horticulture Requirements and test methods . was released . The standard wasASTM E2018 - 15 Standard Guide for Property Condition ASTM E2018 - 15 Standard Guide for Property Condition Assessments:Baseline Property Condition Assessment Process. Active Standard ASTM E2018 Developed by Subcommittee:E50.02. Book of Standards Volume:11.05 :Format:Pages:Price :PDF:21:$75.00:ADD TO CART:Hardcopy (shipping and handling) 21:$75.00:ADD TO CART