EN 10130 DC01/DC03/DC04/DC05/DC06 EN standard of cold-rolled products, grade from commercial quality to deep drawing quality, which can be used in various applications, mainly focus on their deforming properties.
BS EN 10130:2006 - BSI - StandardsBS EN 10130:2006 Cold rolled low carbon steel flat products for cold forming. Technical delivery conditions. BS EN 10130 is an indispensable guide for those who specify, purchase or supply steel, of the standard purchase specifications and delivery conditions of cold rolled narrow strip in coils and cut lengths, in thicknesses up to 10mm and of widths equal to or over 600mm, made from
DESCRIPTION. This standard BS EN 10130:2006 Cold rolled low carbon steel flat products for cold forming. Technical delivery conditions is classified in these ICS categories:77.140.50 Flat steel products and semi-products. This European Standard applies to cold rolled uncoated low carbon steel flat products in rolled widths equal to or over 600 mm for cold forming, with a minimum thickness of 0,35
Cold Rolled Steel - Decoiled & Standard Lengths - Cold COLD ROLLED STEEL SHEET AND COIL - (DC01 BS EN 10130:2006) Cold rolled steel, (often referred to as Cold reduced or CR), is a low carbon product, produced using raw material such as coke and coal at steel mills through out the world. Cold Rolled Process
Cold Rolled Steel Coil and SheetCold Rolled Steel Coil Standard:JIS G3141 :SPCCSPCDSPCE GB Q195Q235 GB/T5213-2008 :DC03DC04DC05 Q/BQB 419-2009 :HC260LAHC380LAHC420LAHC260PHC300PHC260Y Application of Cold Rolled Steel Coil:Cold-r
The most frequently followed European standards for producing cold-rolled coils are EN 10130, EN 10268 and EN 10209. EN 10130 is applied to cold-rolled coils made of the low-carbon DC01, DC03, DC04, DC05, DC06 and DC07 steel grades for cold forming without coating, with a minimum width of 600 mm and a minimum thickness of 0.35 mm.
DIN EN 10139:2016 - Cold rolled uncoated low carbon steel Cold rolled uncoated low carbon steel narrow strip for cold forming - Technical delivery conditions; German version EN 10139:2016. This European Standard applies to cold rolled narrow strip in coils and cut lengths in thicknesses up to 10 mm and of widths less than 600 mm, made from mild, unalloyed and alloyed steels in accordance with table 1.
Flat Steel Products - El-Rashed1- Cold Rolled Coils:D elivery as per:Standard. Steel grade. EN 10130/95(91) DC01(FePO1) DIN 1623-T1/83. St 12, USt 13, RRSt 13, St 14. DIN 1623-T2/86. USt 37-2 G. ASTM A 568/A 568M. SAE 1006, 1008, 1010. ASTM A 366/A 366M. according to standard. GOST 1050/88. 08, 10 (kp, ps, sp)
Dc01 Steel Cold Rolled Cold Roll Sheet Coil DIN EN 10130 DC01 Size 19 Gauge 1mm Mild Steel MS Cold Rolled Iron Sheet Coils $620.00-$640.00 / Ton 10 Tons (Min. Order)
Steel Material Annealed EN 10130 DC01 Cold Steel Coil EN 10130 DC01 cold steel coil is pre-treated before being cold rolled with a process known as pickling, which uses strong acids to remove scale and other impurities The EN 10130 DC01 cold steel coil is then passed through rollers to reduce its thickness
Steel for forming - EN-Home Page Tata Steel in EuropeRelationship with standards. Cold-rolled steel for forming complies with European standard EN 10130:2006 and is available in the grades shown below. European standard. EN 10130:2006. Grade. DC01. Dimensions and coil weights. Tata Steel can supply cold-rolled steel with the following minimum and maximum dimensions and coil weights.
EN 10130-DC01 Cold Rolled Coil C P S Mn Ti 0.12 0.045 0.100 0.60 - Yield Strength Mpa Tensile Strength Mpa Elongation(Thickness) 140-280 270-410 28 EN 10130-DC03 Cold Rolled Coil C P S Mn Ti 0.10 0.035 0.035 0.45 - Yield Strength Mpa Tensil